QUICK LOAD Liner AutoLength System

The QUICK LOAD® liner AutoLength™ system is designed specifically to minimize downtime, wire feeding and quality issues commonly associated with the liner being cut to an incorrect length.

Short liners are a common root cause of poor wire feeding. Further, a short liner does not have a chance of properly seating in the retaining head — often resulting in “bird-nesting” of the welding wire or premature contact tip failure and wear.

Wire feeding challenges reduce efficiency of the welding process and cause undesirable (and expensive) downtime. A system upgrade to this new innovative product can help improve welding efficiency and reduce costly downtime.  

How It Works

Heard the buzz about our revolutionary QUICK LOAD Liner AutoLength System?  Click here to watch our 3D animation.
  • Housed inside the power pin, this spring-loaded module applies constant forward pressure on the liner, keeping it seated properly in the retaining head
  • Allows for up to one-inch (2.54 cm) forgiveness if the liner is too short
  • Accommodates liner movement during welding 

How It Increases Productivity

  • Reduces issues caused by the liner being cut to an incorrect length
  • Decreases burn-backs caused by misalignment between the liner and the contact tip
  • Improves wire feedability by enhancing wire alignment with the contact tip

Important Note: The QUICK LOAD liner AutoLength system is designed specifically for use with QUICK LOAD liners.

Compatibility

The QUICK LOAD liner AutoLength system is compatible with the following MIG guns when configured with front-loading QUICK LOAD liners:

AutoLength™ Pins

For Miller® Feeders

214-81for 0.035″ – 0.045″ wire; interchangeable with 214-1 power pin
214-91for 0.052″ – 1/16″ wire; interchangeable with 214-1 power pin

For Tweco® #4 Feeders

214-80for 0.035″ – 0.045″ wire; interchangeable with 214 power pin
214-90for 0.052″ – 1/16″ wire; interchangeable with 214 power pin

For Tweco #5 Feeders

214-812for 0.035″ – 0.045″ wire; interchangeable with 214-12 power pin
214-912for 0.052″ – 1/16″ wire; interchangeable with 214-12 power pin

For Lincoln® Feeders

214-87for 0.035″ – 0.045″ wire; interchangeable with 214-7 power pin
214-97for 0.052″ – 1/16″ wire; interchangeable with 214-7 power pin
214-840for 0.035″ – 0.045″ wire; interchangeable with 214-40 power pin
214-940for 0.052″ – 1/16″ wire; interchangeable with 214-40 power pin

For Panasonic® Feeders

214-830for 0.035″ – 0.045″ wire; interchangeable with 214-30 power pin
214-930for 0.052″ – 1/16″ wire; interchangeable with 214-30 power pin

For Fronius® Feeders

214-817for 0.035″ – 0.045″ wire; interchangeable with 214-17 power pin
214-917for 0.052″ – 1/16″ wire; interchangeable with 214-17 power pin
214-841for 0.035″ – 0.045″ wire; interchangeable with 214-41 power pin
214-941for 0.052″ – 1/16″ wire; interchangeable with 214-41 power pin

For Euro Feeders

425-820Efor 0.035″ – 0.045″ wire; interchangeable with 425-20E power pin
425-920Efor 0.052″ – 1/16″ wire; interchangeable with 425-20E power pin

For L-Tec® Feeders

214-84for 0.035″ – 0.045″ wire; interchangeable with 214-4 power pin
214-94for 0.052″ – 1/16″ wire; interchangeable with 214-4 power pin

For OTC Daihen® Feeders

214-839for 0.035″ – 0.045″ wire; interchangeable with 214-39 power pin
214-939for 0.052″ – 1/16″ wire; interchangeable with 214-39 power pin

Additional wire sizes may be available. Please contact Customer Service to inquire.