How To Install an LSR Unicable Extension Important Note: If you find that your cable is too short and the power pin won’t plug into the feeder, please use the 1″ cable extension. Thread the 414-700EX-01 cable extension into the brass block of the LSR Unicable and torque to 18 ft.-lbs. Thread power pin clockwise […]
read more...How To Install the LSR+ Flange on an OTC Daihen Robot Note: The following instructions are applicable for OTC Daihen® robot models NB4, NB4L, FD-B4 and FD-B4L Slide one half of the clamp between LSR+ Unicable and robot wrist. Make sure LSR+ clutch cable slot is facing up. Take second half of the clamp and […]
read more...How To Install a TOUGH GUN ThruArm Robotic MIG Gun onto a Motoman Robot Note: The following installation instructions are applicable to installing TOUGH GUN® TA3 robotic air-cooled MIG guns on Motoman® MA1440, MA2010 and MA3120 robots Step 1: Aluminum Spacer Installation Step 2: LSR Unicable Installation into Connector Step 3: Connector, Outer Cover, Power […]
read more...How To Install a TOUGH GUN TA3 MIG Gun on a Panasonic Robot Important Note: The following instructions are applicable for installing TOUGH GUN® TA3 robotic air-cooled MIG guns on Panasonic® TM-1100, TM-1400, TM-1600 and TM-1800 Robots Step 1: Transition Flange and Spacer Installation Step 2: LSR Unicable Installation into Connector Step 3: Connector Installation […]
read more...How To Install Front-End Air Blast for TOUGH GUN ThruArm Series MIG Guns Step 1: Remove the 2 screws which retain Item #1 and slide cover back to expose Item #2. Locate Items #2 and #3 and remove both pieces. Once Items #2 and #3 have been removed, remove Item #4 from the front housing […]
read more...How To Install an LSR Flange on an ABB Robot Note: The following instructions are applicable for ABB® IRB1600ID, IRB1520ID, IRB2600ID and IRB1660ID robot models Secure the LSR Flange on the robot wrist with M6x1.0-25mm LG SHCS. Slide the LSR Unicable through the robot wrist and LSR Flange. Install the LSR Unicable on the TOUGH […]
read more...How To Install or Replace the PER-2599 Motor The following images detail the installation of new motor PER-2510. This motor is not compatible with the existing mounting bracket on spatter cleaner untis made before March 2012 and may also require new valve assembly ER-2700, series number ER-1635 and lower. The new motor is assembled and […]
read more...How To Install a TOUGH GUN ThruArm MIG Gun Equipped with TOUGH GUN I.C.E. Technology onto a KUKA KR5 HW Robot Remove the neck, consumables and conduit from torch. Slide the torch through robot wrist and conduit. Secure the torch on robot wrist. Secure the conduit with two clamps and M5 SHCS. Connect the torch […]
read more...How To Install or Remove Wire Brake on a TOUGH GUN G2 Series Robotic MIG Gun Important Note: This product is factory set for wire equal to or smaller than 0.045”. If you are using wire 0.052” and larger, please remove and replace the wire guide within the neck housing and replace it with the […]
read more...How to Replace QUICK LOAD Liners into Retainer or AutoLength Pin 1. Remove consumables (nozzle, contact tip and retaining head). 2. Pull the existing QUICK LOAD™ Liner from the neck using pliers. 3. Remove the protective cap from the new QUICK LOAD Liner. 4. Insert the QUICK LOAD Liner through the neck using the wire […]
read more...How to Install QUICK LOAD Liners When Replacing Conventional Liners 1. Remove the protective cap from the new QUICK LOAD® Liner. 2. Install this liner from the back of the MIG gun with retainer attached (using the same procedure as installing a conventional liner). Future replacements will be done from the front. (Refer to How […]
read more...How To Install the TT3-500 TOUGH GUN Sprayer onto the TOUGH GUN TT3 Reamer The following images and instructions detail the installation of the TT3-500 TOUGH GUN® Sprayer onto the TOUGH GUN TT3 Reamer. Open the box and inspect the items for any noticeable damage to the parts during shipping. The TT3-500 Sprayer should only […]
read more...How To Install the Filter/Regulator Unit to the TOUGH GUN TT3 Reamer The following images and instructions detail the installation of the Filter/Regulator unit onto a TOUGH GUN® TT3 reamer: Remove the Filter/Regulator from the box. Ensure that all the required parts are present (see Figure 1): Filter Body Regulator Pressure Gauge Mounting Bracket Safety […]
read more...How To Install the TT3-NOZ External Nozzle Detection (Home Interrupt Version) TOUGH GUN® TT3 Reamer (Analog Model) Only Step 1: Limit Switch Kit Reamer Installation Step 2: Limit Switch Cable Routing Step 3: Limit Switch Cable Electrical Connection INS095
read more...How to Repair the Cable on a BTB MIG Gun with a T Series Small Straight Handle Remove consumables (Nozzle, Retaining Head, Contact Tip). Remove the liner from the gun. Mount neck in the vise. Disassemble handle and remove switch from leads. Move the handle back. Bend cable behind connector cone. Cut cable at bend. […]
read more...How to Repair the Cable on a BTB MIG Gun with a T Series Straight Handle Remove consumables (Nozzle, Retaining Head, Contact Tip). Remove the liner from the gun. Mount neck in the vise. Disassemble handle and remove switch from leads. Move the handle back. Bend cable behind connector cone. Cut cable at bend. Slide […]
read more...How To Replace the TOUGH GUN CA3 MIG Gun Unicable IMPORTANT: The following instructions pertain to unicable replacement on TOUGH GUN CA3 MIG Guns manufactured on or after April 8, 2015 NOTE: Unicable replacement can be done while the gun is mounted to the robot. There is no need to uninstall the gun before proceeding. […]
read more...FAQ | Pistolet MIG robotise TOUGH GUN CA3 et TA3 English Tregaskiss a compilé une liste de questions fréquemment posées sur les nouveaux pistolets MIG robotiques à refroidissement par air TOUGH GUN® CA3 et TOUGH GUN TA3 et comment convertir les pistolets MIG robotiques à refroidissement par air des séries TOUGH GUN G1 et / […]
read more...How To Install the TOUGH GUN CA3 Gun Connector and Unicable in Place of The Legacy TOUGH GUN G1 Series MIG Gun Remove the nozzle, retaining head and liner (parts not shown). Loosen the neck clamp SHCS using a 5 mm Allen wrench (see ‘A‘ in Figure 1). Remove the neck (see ‘B‘ in Figure […]
read more...FAQs | TOUGH GUN CA3 and TA3 Robotic Air-Cooled MIG Guns Frequently Asked Questions About the New TOUGH GUN CA3 and TA3 MIG Guns and How To Convert From TOUGH GUN G1 and G2 Series Français Tregaskiss has compiled a list of frequently asked questions about the new TOUGH GUN® CA3 and TOUGH GUN TA3 […]
read more...How To Install the TOUGH GUN TT3 Reamer Sprayer Valve Retrofit Kit (Part #TT3-500R) Required Tools: 9/16″ wrench 11/16″ wrench 5 mm Allen key 3 mm Allen key 2.5 mm Allen key Precision flat head screwdriver Wire strippers Installation Instructions Disconnect power and air. Identify your anti-spatter source (bulk-feed or Tregaskiss supplied reservoir). Disconnect the […]
read more...New Liner Trim Lengths
read more...How To Install or Replace a Euro Power Pin on a BTB Platform Gun Remove liner and strain relief from the gun assembly. Disconnect the Euro block leads from the gun by cutting as close as possible on both sides of the butt connectors in order to preserve wire for later retermination. Slide adaptor nut […]
read more...How To Install or Replace a Bernard Quick Disconnect on a Best of the Best Platform MIG Gun Remove liner from gun assembly. Viewing quick disconnect from cable end, align wave spring and large snap ring with opening access slot. Compress large snap ring with internal snap ring pliers and remove locking sleeve. Remove small […]
read more...